How to Re-deck the Pontoon With New Carpeting

When my husband and I purchased a 1998 Fisher pontoon boat for what we thought was a steal, one of the first things we needed to do is replace the dry-rotted carpet. The pontoon had been sitting in the sun for ten years and the carpet was torn and had areas of dry-rot. As soon as the boat season was over my husband started tearing down the pontoon. Here is what we did to bring an old pontoon back to life.

Right Angle Cordless Drill

Materials that could be needed for this project: camera, paper & marker, zip-loc bags, treated plywood to cover the deck, stainless steel hardware, carpeting (marine or indoor/outdoor), power drill, cordless screwdriver, carpet glue, paint roller or trowel, floor roller or rolling pin, sharp scraper, sandpaper, clamps, stainless steel staples & a stapler,

Right Angle Cordless Drill

Step 1

Take pictures of your pontoon so that you have a visual memory of where things go. Use zip lock bags and labels to keep track of all the hardware. Disconnect all the wiring to the console and labeled it to be sure that you will be able to re-connect everything properly.

Step 2

Draw a diagram of the deck and include precise measurements. Then go back and measure again to be sure you have it all right.

Step 3

Check all the under deck wiring and the hardware to make sure that everything is tight. Be sure to pay special attention to the fittings in the transom area where most loose bolts are found.

Step 4

Remove the furniture, railings and the edge cap.

Step 5

If the deck is questionable, tear it out and replace it with. This material is a chemically-treated wood that excels in weathering harsh marine conditions and has an incredibly long lifespan. Lay all the new sheets of treated plywood on top of the old plywood to mark all the areas that need to be cut, marked, or drilled. Then remove the old plywood. Place the new plywood on the cross members. Install the fasteners on the cross members where the wood is not butted together. Use at least three fasteners on the entire cross members.

Step 6

Roll out the carpet on your clean deck to insure that you have enough to cover the deck, and then put it somewhere handy until it is needed. If the carpet came on a heavy duty cardboard roll, save it for later to use as a roller. The color of your carpet is a very important detail to consider. Remember that dark colors attract and hold the heat. Light colors will get dirty faster but they will not require you to wear your shoes because the carpet is too hot to walk on.

Step 7

If your plywood is still in good condition, you will need to remove the old carpeting. Use a sharp knife and cut the carpet in strips at the deck joints and pull the strips up by hand. There's a good chance that some bits of carpet backing or other residue will be left over and you don't want lumps in your new carpet, so use a sharp instrument and scrape off as much of this stuff as possible. Some bits might stubbornly refuse to come off with a knife, so you may want to use a heat gun and a scraper to remove the residue. In extreme cases, you might have to sand off the residue with sandpaper or even a belt sander.

Step 8

Use a paint roller to apply a liberal amount of glue on the deck. Two gallons of glue are recommended for a 16 foot deck. Allow the water to "flash out" of the glue before applying the carpet.

Step 9

When the glue is tacky to the touch but before it turns clear, apply the carpet. This should be done when the temperature ranges above 60° F and when the humidity is not too high. The cooler the temperatures (and the higher the humidity), the longer it will take for the glue to dry. It is suggested that you have the deck out of the elements and you wait at least 24 hours even when all the conditions are optimal.

Step 10

Lay the carpet down in the rear first. Roll out the carpet flush with the edge. Keep it tight and straight. Work out the wrinkles with your hands by pulling the carpet toward the front and sides. An efficient way to install the carpeting is to lay the carpet down all at once, fold one half of the carpet back, and apply the glue while paying special attention to coat the edges. Then, lay the glued half down and use a roller to smooth out any air bubbles. Repeat this process on the second half of the carpet. The glue should dry in an hour or so.

Step 11

Staple the carpet along the rear with stainless steel staples

Step 12

Using a floor roller, rolling pin, or even the cardboard tubing the carpet came on, roll the carpet to ensure that the carpet is in contact with the plywood.

Step 13

Staple the rest of the edges and trim any excess carpet. Install the edge cap first. Set the entire rail on the deck and align it in position. Use clamps to keep it in place. Some people suggest that you use all new stainless steel hardware. In our case we were able to re-use the hardware that we removed.

Step 14

Pull out the pictures to use to re-install the hardware. Start with the edge cap then place the railing back in its proper location. Clamp the railings in place. Set all furniture on the deck and fasten it down using stainless steel fasteners with fender washers.

Step 15

Re-install the steering, throttle, and shift cables. Re-inspect the pontoon's steering by turning the steering left and right prior to the next launch to insure a safe maiden voyage in your almost new pontoon.

Step 16

Now it is time to protect your almost new pontoon with the purchase of a low cost, 4 or 5 year warranty pontoon cover. This cover should eliminate the extra cleaning needed after the last rain storm or the seagull's last fly-over and it will sustain the look of your new carpet for a reasonable length of time instead of showing the rapid deterioration of the carpet that has been left out in the sun for long periods of time.

How to Re-deck the Pontoon With New Carpeting
Right Angle Cordless Drill

Special Price!!! Makita TD020DSEW 7.2-Volt Lithium-Ion Cordless Impact Driver Kit

Oct 27, 2011 02:04:20

Makita TD020DSEW 7.2-Volt Lithium-Ion Cordless Impact Driver Kit
Click for larger image and other views

Makita TD020DSEW 7.2-Volt Lithium-Ion Cordless Impact Driver Kit

>> Click here to update Cheapest prices for Makita TD020DSEW 7.2-Volt Lithium-Ion Cordless Impact Driver Kit <<

Makita TD020DSEW 7.2-Volt Lithium-Ion Cordless Impact Driver Kit Feature

  • Makita-built motor delivers 177 in.lbs. of Max Torque, with 2,300 RPM and 3,000 IPM
  • Compact design at only 1.1 pounds for reduced operator fatigue
  • Quick release 1/4-inch hex chuck, built-in LED light illuminates work area
  • Lithium-ion battery and Energy Star rated charger produce 430% total lifetime work, 2.5X more cycles
  • 3-year warranty on tools; 1-year warranty on batteries and charger


Makita TD020DSEW 7.2-Volt Lithium-Ion Cordless Impact Driver Kit Overview

The most powerful in-line screwdriver to date! Why? Well, two reasons: it sports the extended run time, high energy output Lithium-Ion batteries, and it's also an impact driver. It may seem unbelievable to have an impact driver so small, but it’s true. An impact driver hammers the chuck laterally to give increased torque to drilling and driving operations, as opposed to just relying on the motor to spin the chuck. This powerhouse provides 12-volt power, with Lithium-Ion and impact energy, in only 7.2 volts. This sweet little tool offers twice the torque of other 7.2 volt in-line screw drivers and any other in its class. Most in-line screw drivers are only 3.6 volts. This new Makita tool offers twice the voltage, twice the power and twice the run time of standard models.

Other great features include a comfortable rubber grip, an easy to reach thumb on/off switch and the easiest to use, all-metal, quick-change, hex, Insty bit chuck. The chuck only accepts drill bits and driver bits that have a hex shank at the opposite end of, for example, a no. 2 Phillips driver bit. This really speeds up bit changes. Hex Insty bits have really become the standard and are offered in every drill bit kit available. There is an accessory Makita chuck that converts the quick-change hex bit chuck into the older style 3-jaw chuck that will accept round shank drill bits, so you can use your existing bits.

What I like most about this tool is it bends nearly 90 degrees for controlled driving. Driving in-line is great for fast, light-duty driving. For example, electricians use these tools for installing wall plates over outlets and switches. Driving at a right angle is used for driving longer screws and driving/drilling where more controlled accuracy is needed. This tool also has an LED light under the chuck that illuminates the work area, which is great for working in dark cabinets and under shelves. -- Gabriel Shantara Ford

What's in the Box
Battery, charger, one drill bit, two driver bits, a tool holster with belt loop (not a clip-on), padded carrying case.

Makita TD020DSEW 7.2-Volt Lithium-Ion Cordless Impact Driver Kit Specifications

Makita's 7.2V Lithium-Ion Cordless Impact Driver delivers convenience and compact power to the jobsite. The TD020DSEW combines the ultra-compact design of a cordless screwdriver with the function of an impact driver for a range of driving and fastening tasks.



View larger


View larger
TD020DSEW Features
POWER - Ultra-compact impact mechanism yields 177 in.lbs. of Max Torque
COMFORT - Only 1.1 lbs. with contoured grip
SPEED - Delivers 3,000 rotational impacts/min. and 2,300 RPM (non-variable speed)
CONVENIENCE - Operates in straight or pistol grip positions
INCLUDES - Two 7.2V Li-Ion batteries, charger and case

Tool Specifications
Hex shank1/4"
No load speed2,300 RPM
Impacts per minute3,000 IPM
Maximum torque177 in.lbs.
Battery7.2V Lithium-Ion
Overall lengthPistol (8-3/8"), In-Line (10-7/8")
Net weight1.1 lbs. (w/battery)
Makita-Built Motor Engineered for Versatile Power
The TD020DSEW is powered by a Makita-built motor with dual steel ball bearings, and delivers 177 in.lbs. of Max Torque with 2,300 RPM and 3,000 impacts-per-minute in an ultra-compact design. The TD020DSEW will operate in straight or pistol grip positions. Makita's proprietary hammer and anvil impact mechanism are manufactured using the best raw materials with the highest quality steel and unique heat hardening process for maximum fastening and driving power.

Ergonomic Design in a Compact Size
The TD020DSEW weighs just 1.1 pounds with a more compact design at only 10-7/8 inches long (extended) and 8-3/8 inches long (pistol), with an ergonomic shape that fits like a glove for reduced operator fatigue. The TD020DSEW is also equipped with a built-in L.E.D. work light operated by a separate switch on the opposite side of the rocker, and provides illumination for more accurate work. The switch drive lock prevents active discharge in the case when not in use, and allows the tool to be a screwdriver in lock position.

Versatile Design for a Range of Applications
The TD020DSEW can drive deck screws into up to 16 gauge sheet metal, drill a 3/8-inch hole into hardwood, and drive a 1/4-inch screw with a nut setter bit. The tool's versatile power, combined with the compact design, dual position handle, and powerful Makita impact mechanism makes this tool perfect for automotive, installation, repair, and fabrication trades, or for any pro contractor requiring a best-in-class engineered cordless impact screw driver. The TD020DSEW is just another example of Makita's commitment to innovative technology and best-in-class engineering.

About Makita's Lithium-Ion Cordless Tool Series
As one of the pioneers driving the cordless tool revolution, Makita changed the game with its breakthrough 18V LXT Lithium-Ion Cordless Series. Three years after its debut, Makita's LXT Series has grown from seven to over 35 tools, providing a wide range of cordless solutions for professional tradesmen. Makita also added 18V Compact Lithium-Ion for cordless power in a more compact size. Makita now offers 10.8V Ultra-Compact Lithium-Ion and 7.2V Lithium-Ion cordless power tools. These cordless tools deliver pro power and pro speed in an ultra-compact size. The battery charging system for the 10.8V and 7.2V Lithium-Ion batteries is ENERGY STAR rated for its efficient charging process. Makita's growing line of ultra-compact cordless tool solutions includes driver-drills and impact drivers, as well as rechargeable flashlights and several different combo kits.

About Makita
Makita is a worldwide manufacturer of industrial quality power tools and offers a wide range of industrial accessories. Makita applies leading-edge innovation to engineer power tools that are more compact and energy efficient, yet deliver industrial strength power and results. Makita U.S.A., Inc. is located in La Mirada, California, and operates an extensive distribution network located throughout the U.S. For more information, please call 800/4-MAKITA (800/462-5482) or visit makitatools.com. Makita is Best in Class Engineering.

Warranty
Every Makita Lithium-Ion tool is backed by Makita's 3-Year Warranty that covers repair due to defects in materials or workmanship up to three years from the date of original purchase. Makita Lithium-Ion batteries and chargers have a limited 1-year warranty. Please see makitatools.com for complete details.

What's in the Box
Makita TD020DSEW 7.2-Volt Lithium-Ion Cordless Impact Driver Kit, two 7.2V Lithium-Ion batteries, 30 Minute Charger, two Phillips/one slotted fastening bits, and tool case.




SAVE NOW on the special offers below!

Available In Stock.

This Makita TD020DSEW 7.2-Volt Lithium-Ion Cordless Impact Driver Kit ships for FREE with Super Saver Shipping.

Price : Click to Check Update Prices Please.

Makita TD020DSEW 7.2-Volt Lithium-Ion Cordless Impact Driver Kit

Limited Offer Today!! Makita TD020DSEW 7.2-Volt Lithium-Ion Cordless Impact Driver Kit Black Friday and Cyber Monday Deals

Contours Kolcraft Stroller Saw Laser